| Metric Felt Company | |||
| Laminate Adhesive Series | |||
| Product Series | Description | Data Sheet | |
| A100 | General purpose. Bonds well to HSE plastics, metals, polyester foams & mildly plasticized foam | See More | |
| A175 | Permanent/removable. Designed for removability from non-paper substrates | See More | |
| A200 | Aggressive acrylic. Bonds well to HSE foams & rubbers as well as ether urethanes with heat assist | See More | |
| A200T | Same as A200 but with a tenslized carrier | See More | |
| A210 | Nonwoven carrier. Very high levels of adhesion | See More | |
| A500 | Designed for high temperature wrap-around applications | See More | |
| A501 | General purpose laminating and fabricating applications. Good balance of tack, peel and shear | See More | |
| A505 | Nonwoven carrier. Designed for high temperature wrap-around applications | See More | |
| A601 | General purpose laminating and fabricating applications. 2 mil polyester carrier | See More | |
| Product Series | Description | ||
| B93 | General Purpose. Same as B95 but with a PP carrier | See More | |
| B95 | General Purpose. Excellent adhesion to HSE & LSE foams, plastics, painted metals. 60# Kraft liner | See More | |
| B96 | Same as B95 but with 80# liner | See More | |
| B97 | Same as B95 but with a board liner | See More | |
| B100 | Excellent adhesion to ester urethane foams, LSE plastics & mildly plasticized rubber formulations | See More | |
| B140 | Nonwoven carrier. Designed for wrap around applications. Bonds well to talc filled PP | See More | |
| B600 | High adhesive mass. PET carrier. For demanding applications | See More | |
| B623 | High adhesive mass. For demanding applications. Higher peel values than B600. Non-oriented film carrier | See More | |
| Product Series | Description | ||
| BA150T | Acrylic adhesive on foam side has excellent adhesion to a wide variety of materials. Rubber adhesive | See More | |
| C100 | Designed for applications where urethane foam is bonded to PP. Excellent adhesion to esters & ethers | See More | |
| C100-STDFR | Same as C100 but with flame retardant additive in the adhesive | See More | |
| C102 | High performance. Designed for applications where urethane foam is bonded to PP, PE, TEO and TPO | See More | |
| C108 | Similar to C102 but with lower coat weight of adhesive | See More | |
| C200 | Used where a mildly plasticized material or a urethane foam must have an aggressive rubber adhesive for bonding to LSE substrates | See More | |
| C500 | For demanding wrap-around applications where high temperature is involved | See More | |
| C501 | Similar to C500 but with lower coat weights | See More | |
| C610 | Similar to C690B with a lower coat weight on the foam/unwind side. No biocide | See More | |
| C690B | Applications where urethane foams are bonded to PP, PE, TEO & TPO. Contains biocide | See More | |
| Product Series | Description | ||
| 2119SL | 2MIL polyester film coated with a permanent solvent rubber adhesive. Designed to act as a stiffener for urethane foams and sponge rubber. Adhesive is not suited for direct exposure to UV light | ||
| 2122SL | 5MIL polyester film coated with a permanent solvent rubber adhesive. Designed to act as a stiffener for urethane foams and sponge rubber. Also available with a 10MIL polyester. Adhesive is not suited for direct exposure to UV light | ||
| 2118SL | 2MIL polyester film coated with a permanent solvent acrylic adhesive. Designed to act as a stiffener for urethane foams and sponge rubber | ||
| 2116SL | 10MIL polyester film coated with a permanent solvent acrylic adhesive. Designed to act as a stiffener for urethane foams and sponge rubber | ||
| Product Series | Description | ||
| F10-37.5" | Good balance of tack, peel and shear. Not recommended for use on LSE substrates | See More | |
| F5227 | 4.5MIL low-fogging permanent acrylic designed for adhesion on LSE substrates | See More | |
| DLF-3276 | 3 mil acrylic. Good for high temperature wrap-around applications | See More | |
| DLF-5276 | Same as DLF-3276 but with 4.5 mils of adhesive | See More | |
| F9200 | 2 mil rubber. Designed for difficult assembly aid wrap applications on LSE plastics | See More | |
| F9500 | Same as F9200 but with 5 mils of adhesive | See More | |
| Product Series | Description | ||
| A902 | 1.0mm black flocked fabric with permanent acrylic. PSA designed to meet all requirements of GM6420M Type 1B, PF-10770, MS-JZ8-22 | See More | |
| A904 | 1.0mm white flocked fabric with permanent acrylic. PSA designed to meet all requirements of GM6420M Type 1B, PF-10770, MS-JZ8-22 | See More | |
| A912 | 1.0mm white flocked fabric with permanent acrylic. PSA designed to meet all requirements of GM3622M Type IV Cycle D & MS-JZ8-22 | See More | |
| A915 | 1.5mm black flocked fabric with permanent acrylic. PSA designed to meet all requirements of ESB-M6G17-A & all specs from A902 series | See More | |
| Product Series | Description | ||
| DLA-504 | High performance product designed for high temperature wrap around applications | See More | |
| DLC-401 | High performance product with a high shear rubber on the end user side and a high shear acrylic on the laminating side | See More | |
| DLC-503 | Nonwoven supported acrylic-silicone adhesive for laminating to silicone sponge rubbers w/o the use of a flammable primer | See More | |
| B1116-White | Double coated white 1/16" PE foam with rubber adhesive | See More | |
| B1116-Black | Double coated black 1/16" PE foam with rubber adhesive | See More | |
| B1132-White | Double coated white 1/32" PE foam with rubber adhesive | See More | |
| B1132-Black | Double coated black 1/32" PE foam with rubber adhesive | See More |